Introduction and Setup Impressions

Netgear launched the 6-bay ReadyNAS 716 10-GbE desktop NAS in November. To our knowledge, this is the first off-the-shelf NAS in a desktop tower form factor to come with built-in support for 10GBase-T. With an Intel Xeon CPU under the hood, the unit packs quite a punch within a small form factor. 10-GbE solutions have remained in realm of rackmount units so far, but, Netgear, along with QNAP (in its TS-x70 series), aims to bring them to desktop form factors also. While the QNAP TS-x70's 10-GbE capabilities are optional (the end user has to change the PCIe add-on card for that purpose), the ReadyNAS 716 comes with a two-port 10GBase-T NIC installed.

Netgear's storage lineup has been in a bit of flux over the last few years. While the x86-based versions have been quite stable, their SOHO / home consumer lineup had to shift from SPARC-based units to ARM-based ones. We covered the reboot of the ReadyNAS OS for ARM-based units in the review of the ReadyNAS NV+ v2. Despite Netgear's promise to work on adding features and making the new ReadyNAS OS better to use, here we are, two years later, looking at yet another reboot of the ReadyNAS OS. The reboot aims to unify the product features across both ARM and x86-based units. We already reviewed the ReadyNAS 312, which happens to be the entry-level x86-based NAS in Netgear's 2013 lineup. The ReadyNAS 716 (RN716X) is Netgear's flagship in the 2013 desktop form factor category. Based on the Intel Xeon E3-1265L processor, the unit runs the completely revamped ReadyNAS OS 6.

In terms of redesign, ReadyNAS OS 6.0 is the most ambitious yet. Unlike other NAS vendors who opt for the safety of the proven EXT3 / EXT4 file system for internal volumes, Netgear has opted for the cutting-edge BTRFS. The benefits of BTRFS over EXT3 / EXT4 are numerous. These include checksumming for integrity, in-built snapshotting mechanisms, continuous defragmentation, online data compression, scrubbing with error correction and built-in storage pools which make a separate LVM unnecessary. Compared to ZFS, the memory requirements are more manageable, but, deduplication support in ZFS is much better. However, there is an impression amongst some IT folks that btrfs is not stable enough for deployment in production environments. Netgear indicates that btrfs is part of Oracle's production kernel and, currently, the same code and kernel are being used in ReadyNAS OS 6.x.

The specifications of the RN716X are provided below:

The ReadyNAS 716 runs a Linux kernel (v3.0.93). Other interesting aspects of the system can be gathered after obtaining SSH access to the unit.

The RN716X has an in-built 200W PSU. While enterprise rackmount units with similar platforms have redundant PSUs, the form factor of the RN716X precludes that feature. The motherboard has two native GbE ports, while the 10GBase-T ports are provided by an add-on PCIe card. After connection to the network, the unit could be discovered by RAIDar (offline discovery tool that has been around since the first generation ReadyNAS units). In addition, Netgear has also incorporated cloud discovery using the ReadyCLOUD service. I had faced issues in trying to start out with previously used disks while evaluating the RN312, but the issue was not much of a problem with the RN716X. The front panel has a LCM display as well as a touch-sensitive interface to navigate the options on the display.

We have already touched upon the various features of ReadyNAS 0S 6.x in our ReadyNAS 312 review. The snapshotting mechanism used by Netgear is quite advantageous in the market segment that the RN716X targets. The only surprise in our setup process was the fact that the Flex-RAID configuration (allowing users to manually control the RAID level) didn't allow for RAID-1 to RAID-5 migration when adding a third disk to an already existing two-disk volume. However, switching to X-RAID enabled this option without data loss. The volume could be converted back to Flex-RAID after completion of the migration.

In the rest of the review, we will cover the testbed setup and testing methodology, putting focus on our updates to enable testing 10GBase-T equipment. This is followed by benchmarks in single and multi-client modes. For single client scenarios, we have both Windows and Linux benchmarks with CIFS and NFS shares. We will also have some performance numbers with encryption enabled. In the final section, power consumption numbers as well as RAID rebuild times will be covered along with some closing notes.

ncG1vNJzZmivp6x7orrAp5utnZOde6S7zGiqoaenZIR3fJdopZ6sl5qus3nRnpidsZ6WwG6DkG9kq52mnrK4eZBpnpuZo5rBbrXNZphmnJWouLW7z2almqs%3D